Cricket Free, no account Runs in your browser

Cricket Run Rate Calculator

Turn runs and overs into a scoring rate — with overs-and-balls notation handled properly, not as decimal overs.

Updated 17 Nov 2026 Live calculation

Run rate calculator

19 overs and 4 balls is written 19.4 — enter the two parts separately.

19 overs + 4 balls = 118 balls faced
Scoring rate Runs per over
9.51 rpo at this innings rate
Balls faced
118
Decimal overs
19.67
Projected 50-over total
475 runs
Runs per ball
1.58

187 ÷ (118 ÷ 6) = 187 ÷ 19.67 = 9.51

Overs count legal deliveries only. Why 19.4 ≠ 19.40

How run rate is calculated

Run rate is the average number of runs scored per over. The tricky part is not the division — it is the notation. Cricket overs are a base-6 system: six legal balls make an over, so 19.4 does not mean 19.4 decimal overs.

1. Total balls = (overs × 6) + balls
2. Decimal overs = total balls ÷ 6
3. Run rate = runs scored ÷ decimal overs

This calculator converts your overs and balls into a single ball count first, then divides. That prevents the most common run-rate error: dividing runs by the scoreboard notation as if it were a decimal.

Why the ball count comes first

A rate is an average over a workload. Once the workload is expressed in balls, every other figure — decimal overs, runs per ball, projections — follows from it. Working in balls also makes later calculations, such as net run rate, directly comparable.

A worked example

A side scores 187 in 19 overs and 4 balls.

Worked calculation 19.4 overs
Total balls = (19 × 6) + 4 = 118
Decimal overs = 118 ÷ 6 = 19.667
Run rate = 187 ÷ 19.667 = 9.51 runs per over

The incorrect shortcut, 187 ÷ 19.4 = 9.64, overstates the rate because 19.4 is being read as decimal overs.

At the same rate, a full 50-over innings would project to roughly 475 runs. That is a projection from one rate, not a forecast: scoring rarely stays flat through an innings.

Reading the result

A run rate is a snapshot of tempo. It is most useful in context: compared with the opposition, with the required rate in a chase, or with the same team earlier in the competition.

  • In a chase — compare the current rate with the required rate to see whether the batting side is ahead of the ask.
  • In a group table — run rate feeds net run rate, which uses totals across matches rather than an average of match rates.
  • In analysis — a single rate hides phases. A side can score quickly at the start and slowly at the death and finish with the same average.

The projection field applies the current rate to a full 50-over innings. It is included for context and is always described as a projection, never as an expected score.

Limits and edge cases

The calculator uses a simple, transparent formula. It does not model wickets, extras, rain interruptions or revised targets. For a match shortened before it starts, use the overs actually allotted; for a match affected mid-innings, official targets may fall under Duckworth-Lewis-Stern and cannot be recreated with run rate alone.

If a team is bowled out, enter the overs and balls actually faced. The all-out rule belongs to net run rate calculations, not a standalone innings run rate.

Working with a scorecard? Use the overs and balls shown there. Wides and no-balls are already excluded from the ball count, while their runs remain in the total.

Frequently asked questions

What is a good run rate in cricket?
There is no universal number. A good rate depends on the format, the pitch and the stage of the innings. In T20 cricket, sides often target eight runs per over or more; in a 50-over match, a rate around five to six is a common baseline. Treat any benchmark as context, not a rule.
Is 19.4 overs the same as 19.4 decimal overs?
No. In cricket notation, 19.4 means 19 completed overs plus 4 balls, which is 118 balls or 19.667 decimal overs. Dividing runs by 19.4 directly would overstate the workload and understate the run rate.
Which balls count towards overs faced?
Overs are made of legal deliveries. Wides and no-balls do not count as balls faced, although any runs they concede still count in the team total. A scorecard already reflects this, so enter the overs and balls exactly as shown.
Can I use run rate to work out a chase?
Use the required run rate calculator for a chase. It takes the target, current score and balls remaining, then converts them into the rate needed. Run rate alone tells you what has happened, not what is required.
Does this calculator handle rain-reduced matches?
No. It performs the standard run-rate calculation on the numbers you enter. Revised targets under the Duckworth-Lewis-Stern method involve resource percentages and cannot be derived from a simple run-rate formula.

Keep going

More from the toolkit

All tools
01

Required Run Rate

See exactly what a chase needs: runs required, balls left and the rate that gets there.

Cricket
02

Net Run Rate

Build a group-stage NRR from match innings, including the all-out overs rule.

Cricket
03

Points Calculator

Convert wins, draws and defeats into points with your own competition’s scoring rules.

Football